Hobby & Verzamelartikelen van het thema H0 Trix C-Rail

These spade connectors can be used for the contact fingers on C Track. They are for all Märklin wire from 0.19 sq. mm / 0.0003 sq. in. or 0.02 in. diameter to 0.75 sq. mm / 0.001 sq. in. or 0.04 in. diameter. 1 package contains 20 spade connectors.

For retrofitting 2 C Track turnouts. The turnout lanterns can be used right, left or three-way turnouts. They can be used with a manual hand lever and/or with the 74491 electric turnout mechanism. The lights for the lanterns are maintenance-free LEDs.

This is an improved kit for upgrading C Track turnouts. It has a double solenoid mechanism with end shut-off contacts.

To separate power circuits or signal blocks. 8 pieces for 4 insulation points.

This is for retrofitting 2 C Track turnouts. The turnout lanterns can be used right, left, or three-way turnouts. They can be used with a manual hand lever and/or with the 74491 electric turnout mechanism. The lights for the lanterns are maintenance-free warm white LEDs.

The light mast can be plugged into the Märklin 24997 C-Track or Trix 62997 C-track . The mast signal lights up when the uncoupler track is activated. Metal mast. Height 85 mm / 3-38". This light mast is technically the same as the earlier 5113 mast.

R2 = 437,5 mm

R1 = 360 mm

R3 = 515 mm

R4 = 579.3 mm
Parallel curve to Radius R3 with a spacing of 64.3 mm / 2-9/16". 12 sections of track form a circle with an outer diameter of 120 cm / 47-1/4".

6 pieces. 10 x 5 x 1.5 mm / approx. 25/64" x 3/16" x 1/16". This magnet is for activating 7555 reed switches. It is for locomotives with little ground clearance.

From the starter set on with TRIX C Track: The layout's operations grow.

1.6 x 13 mm / 1/16" x 1/2" with cross point head. Contents 200 pieces.

Removable roadbed slope. This track is used on both branches of the wide radius turnouts and wide angle crossings.

A frame with a buffer beam comes mounted on the track. The rails end in the roadbed.

Serves as the complement to the length of the complementary curve on the wide radius turnouts and wide angle crossings.

This track is the same length as the parallel track spacing for the wide radius turnouts and wide angle crossings.

Red and brown feeder wires with spade connectors at both ends, for C Track. Length 2 meters / 78-3/4".

2 pieces. 10 x 10 x 3 mm / approx. 3/8" x 3/8" x 1/8". This magnet is for activating the 7555 reed switch. It is for freight and passenger cars.

The reed switch is for use at a suitable point with K Track or C Track. The reed switch triggers a pulse of current when a locomotive or car with a magnet mounted on the underside passes over it. The connections to the reed switch are potential-free. The reed switch has a maximum current capacity of 2 amps. Length 38 mm / 1-1/2".

R5 = 643,6 mm
Parallel curve to Radius R4 with a spacing of 64.3 mm / 2-9/16". 12 sections of track form a circle with an outer diameter of 133 cm / 52-3/8".

R9 = 1114.6 mm
Complementary curve for the wide radius turnouts. Also suitable for use in constructing sweeping main lines.

Manual hand lever included. Can be retrofitted with a turnout mechanism, a digital decoder and turnout lanterns.

Manual hand lever included. Can be retrofitted with a turnout mechanism, a digital decoder and turnout lanterns.

This track is the same length as the length of the wide radius turnouts.

R1 = 360 mm

R2 = 437.5 mm

Removable roadbed slopes. This track section is required on both branches of the 62771 and 62772 wide radius curved turnouts.
R3 = 515 mm

3 pieces. 13 x 7 x 2.5 mm (approx. 1/2" x 9/32" x 3/32"). This magnet is for activating 7555 reed switches. It is for locomotives with greater ground clearance.

This feeder wire set has spade connectors for C Track. The set has two-conductors with a red and a brown wire.