Hobby & Verzamelartikelen van het thema H0 Märklin C-Track

Two straight track sections, each 94.2 mm / 3-11/16". Continuous contact through wheel sets. With insulated section of rail for track occupation feedback when traversed by a train. Can be extended with regular straight or curved track sections.

This is for retrofitting 2 C Track turnouts. The turnout lanterns can be used right, left, or three-way turnouts. They can be used with a manual hand lever and/or with the 74491 electric turnout mechanism. The lights for the lanterns are maintenance-free warm white LEDs.

Slanke meegebogen wissel.

This feeder wire set has spade connectors for C Track. The set has two-conductors with a red and a brown wire.

To separate power circuits or signal blocks. 8 pieces for 4 insulation points.

This set is for older color light signals (item nos. 7239 to 7242) and semaphore signals (item nos. 7039 to 7042), which come equipped for operation with K or M Track. The set includes center rail insulators, wires for connections, and hardware for one signal block.

Red and brown feeder wires with spade connectors at both ends, for C Track. Length 2 meters / 78-3/4".

The light mast can be plugged into the Märklin 24997 C-Track or Trix 62997 C-track . The mast signal lights up when the uncoupler track is activated. Metal mast. Height 85 mm / 3-38". This light mast is technically the same as the earlier 5113 mast.

The reed switch is for use at a suitable point with K Track or C Track. The reed switch triggers a pulse of current when a locomotive or car with a magnet mounted on the underside passes over it. The connections to the reed switch are potential-free. The reed switch has a maximum current capacity of 2 amps. Length 38 mm / 1-1/2".

Slanke meegebogen wissel.

6 pieces. 10 x 5 x 1.5 mm / approx. 25/64" x 3/16" x 1/16". This magnet is for activating 7555 reed switches. It is for locomotives with little ground clearance.

3 pieces. 13 x 7 x 2.5 mm (approx. 1/2" x 9/32" x 3/32"). This magnet is for activating 7555 reed switches. It is for locomotives with greater ground clearance.

2 pieces. 10 x 10 x 3 mm / approx. 3/8" x 3/8" x 1/8". This magnet is for activating the 7555 reed switch. It is for freight and passenger cars.

This screwdriver has a cross point size 00 (Ph). For 74990 (C) and 7599 (K) track screws.

The feeder wire set comes with interference suppression and overload protection. It includes a circuit board with spade connectors for C Track and a red and a brown feeder wire. One feeder wire set is needed for each conventional track circuit. One 74046 feeder wire set should be installed in each track power circuit to protect against possible radio and television interference caused by locomotives in operation. This feeder wire set also offers effective protection against overloads and short...

For retrofitting 2 C Track turnouts. The turnout lanterns can be used right, left or three-way turnouts. They can be used with a manual hand lever and/or with the 74491 electric turnout mechanism. The lights for the lanterns are maintenance-free LEDs.

24 rail joiners. These are for connecting the rails at the joints of cut sections of C Track. This provides a mechanical joint and a ground contact for the rails.

This decoder can be installed in the C Track three-way turnout (24630) with an electric mechanism. The digital formats supported are mfx, Motorola, and DCC. Connections are with plug contacts, for Märklin and Trix C Track three-way turnouts. An address can be set with coding switches (MM 1–320, DCC 1–511) as well as by CVs (MM 1–320, DCC 1–2044) using the programming track.