Hobby & Verzamelartikelen van het thema Rails en treintoebehoren

Contents: 12 curved tracks 24230, 4 straight tracks 24188, 4 straight tracks 24172. Rail junction box, switching power supply 36 VA / 230 V and mobile station for digital entry. Illustrated play book with many tips and suggestions. Expansion options with the C-track expansion packs and with the entire C-Track program.

1 German Federal Railroad (DB) class 89 steam locomotive, 1 DB low side car with a tarp, 1 gondola.

2 signals on one mast without additional connections. Block signal for use on main lines. Distant signal for use before a block signal or an entry signal.

All of the connections use the new plugs and sockets.Appropriate plugs are included.These connections work the same as the 6083, 6084, and 6088 decoders.

The signal has 2 independent semaphores and an open narrow mast. The signal changes from red to green or red to green/yellow.

The signal has 2 independent semaphores and an open lattice mast. The signal changes from red to green or red to green/yellow.

This is a signal mechanism with integrated circuits for controlled stopping of digital locomotives with high-efficiency propulsion.

The signal has a semaphore and an open narrow mast. The signal changes from red to green.

Detachable solenoid mechanism (75491) included. Crossing angle 22° 30'. Curve same as 2232. Length of the straight side 168.9 mm / 6-5/8".

2 solenoid mechanisms included. Length of the straight side 168.9 mm / 6-5/8". Turnout branches 2 x 22° 30'. Branch radius 424.6 mm / 16-3/4". Curve same as 2232. 2 additional hand levers included. 6 wires for connections.

2 detachable hand levers included. Crossing angle 14° 26'. Curve radius 902.4 mm / 35-1/2". Length of the straight side 225 mm / 8-7/8". 2 each 75491 solenoid mechanisms can be installed on this unit. Separate paths can be set on the double slip switch.

Changes from red (Hp0) to green (Hp1) or green/yellow (Hp2) and controls track power with double solenoid mechanism with additional third solenoid for the green/yellow aspect. 2 additional hand levers. With base plate. Width 30 mm / 1-3/16*. Length 95 mm / 3-3/4*. Height 90 mm / 3-9/16*.

Set screw terminals for all connections.Network cable included.

Yard signal for use in switching areas.Prototypical thin pipe mast.The Sh1 aspect is correct with 2 white lights.

Detachable solenoid mechanism (75491) included. Inner curve 30°. Outer curve 30° in the parallel curve spacing of 64.6 mm / 2-1/2". Length and radius of the inner curve are the same as 2221

Detachable solenoid mechanism (75491) included. Inner curve 30°. Outer curve 30° in the parallel curve spacing of 64.6 mm / 2-1/2". Length and radius of the inner curve are the same as 2221.

Detachable solenoid mechanism (75491)included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8".

Detachable solenoid mechanism (75491)included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8".

The cross span assembly is a pre-assembled unit consisting of span wires, cross span support wires, and 3 adjustable catenary wire hangers. 2 metal tower masts on bases with mounting screws and slide-on connections are included. The mast spacing can be adjusted up to 235 mm / 9-1/4". The span wires are made of welded steel wire, the cross span support wires are elastic, and the masts and catenary wire hangers are electrically separated from each other. Mast height 150 mm / 5-7/8".

The signal has a movable disk. The signal changes from yellow/yellow to green/green. It has a double solenoid. A base plate is included.Width 28 mm / 1-1/8". Length 65 mm / 2-9/16". Height 73 mm / 2-7/8".

This decoder can be installed in the C Track three-way turnout (24630) with an electric mechanism. The digital formats supported are mfx, Motorola, and DCC. Connections are with plug contacts, for Märklin and Trix C Track three-way turnouts. An address can be set with coding switches (MM 1–320, DCC 1–511) as well as by CVs (MM 1–320, DCC 1–2044) using the programming track.

Retrofit kit for all modern 26.4 cm / 10-3/8", and 27 cm / 10-5/8" Märklin H0 cars with guide mechanisms.

66 Stekkers en 34 moffen. Op kleur gesorteerd bij gemiddeld gebruik.

Slanke meegebogen wissel.

Changes from yellow/yellow (Vr0) to green/green (Vr1). With 7230 mounting bracket and base plate. Width 16 mm / 5/8*. Length 28 mm / 1-1/8*. Height 67 mm / 2-5/8*.

Changes from yellow/yellow (Vr0) to yellow/green (Vr2). With 7230 mounting bracket and base plate. Width 16 mm / 5/8*. Length 28 mm / 1-1/8*. Height 67 mm / 2-5/8*.

This is a metal round mast and has a metal hanger arm. A base with a mounting screw and a slide-on connection is included. An additional base as a clip for C Track is included. Feeder wire for C Track included. Height 100 mm / 3-15/16". 5 pieces to a package.

Crossing angle 14° 26'. Track length 225 mm / 8-7/8".

For cars 43581-43586. The kit consists of a pickup shoe and a ground spring, a circuit board with 10 light bulbs, and a current-conducting coupler.

This decoder can be installed in all C Track turnouts with an electric mechanism. The digital formats supported are mfx, Motorola, and DCC. Connections are with plug contacts. An address from 1 to 256 can be set with coding switches.

Double solenoid mechanism with feedback contacts, end position shutoff, and a locking feature. The turnout mechanism can be mounted on the 5965, 5966, 5976 and 5977 turnouts. It can be operated by remote control using the 7272/72720 or 7271/72710 control boxes (conventional operation) or the 6083/60830 k 83 decoder (digital operation). 3 hookup wires included. Dimensions 67 x 41 x 17 mm / 2-5/8" x 1-5/8" x 5/8".

Component for programming and reading H0 locomotives with built-in c 82 decoder. Can be used in code locomotive addresses, starting voltage, and acceleration and braking delay.

The relay has 4 single-pole switches. The contacts have a 2 amp capacity. The relay can be activated by a control box, circuit track, contact track, reed switch, or digital decoder.

This decoder can be installed in the C Track three-way turnout (24630) with electric mechanisms. It can be used with the digital formats Motorola and DCC. Connections are made with plug-in contacts, for Märklin and Trix C Track turnouts. An address can be set with coding switches (Motorola Format 1 to 320 / DCC Format 1 to 511), and can also be set on the programming track. Turnout lanterns can be connected and can be controlled (soldering skills required). A digital decoder can be installed...

Voor uitbreiding van de C-rail startset met een rangeerspoor.

This kit is for a custom set-up. It consists of cross span wires, cross span support wires, insulators and 5 catenary wire hangers. 2 tower masts (74142) are required at a distance of up to 500 mm / 19-11/16". The cross span wires are made of steel; the cross span support wires can be realistically tensioned. The catenary wire hangers are electrically insulated. This kit comes with set-up instructions.

Same as 7330, but for shorter express train passenger cars. For cars 41351, 41361, 42383 and 42751.

For cars 42101, 42131, 4214, 42141, 42142 and 4229. The kit consists of a pickup shoe and a ground spring, a light diffuser, a light socket and a light bulb.

For cars 4131, 4132 and 4133. The kit consists of a pickup shoe and a ground spring, an adjustable light diffuser, 2 light sockets and 2 light bulbs.

For cars 42168, 42171, 4227, 4255-4257, 42551-42571, 4264, 4265, 4282, 4285, 4286, 4327, 4368, 4369 and 4384. The kit consists of a pickup shoe and a ground spring, a light diffuser with light sockets and 2 light bulbs. This kit can be used with the 7319 current-conducting close coupler.

Install from below on a locomotive.

Longer connecting cable for the 6088 and 60880 s 88 decoders. Length 200 cm / 78-3/4".

Detachable hand lever included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8". A 75491 solenoid mechanism can be installed on these turnouts.

This is an improved version of the 7549 turnout mechanism. This mechanism can be used with the 2265 and 2266 turnouts (new versions), the 22715 and 22716 turnouts, the 2275 double slip switch, and the KOMBI extension set program. The mechanism has an automatic end shutoff feature. Automatic feedback is possible with the 72710 control box. Below-baseboard mounting can be done with the 7548 installation kit.

One each right and left turnout lantern for installation on turnouts with the detachable turnout mechanism. The turnout lantern can be used with hand levers, the 75491 turnout mechanism, or the 7548 below-baseboard mounting kit with a 7549. The lights are maintenance-free LEDs.

Type SBS 10 for older design locomotives. Interchangeable with 7218.

Type SBS 65 for modern locomotives. Interchangeable with 7218.

The feeder wire set comes with interference suppression and overload protection. It includes a circuit board with spade connectors for C Track and a red and a brown feeder wire. One feeder wire set is needed for each conventional track circuit. One 74046 feeder wire set should be installed in each track power circuit to protect against possible radio and television interference caused by locomotives in operation. This feeder wire set also offers effective protection against overloads and short...

Signal control box for the 70361, 70381, 70391, 70392, 70411, 70412, and 70421 semaphore/target signals and for the 764xx series color light signals. This control box is for operating up to 4 signals. A multi-conductor cable with plugs is included for connecting control boxes together.

For cars 4085 and 4087. The kit consists of a pickup shoe, light diffuser, 2 light sockets, and 2 light bulbs.

This is an improved kit for upgrading C Track turnouts. It has a double solenoid mechanism with end shut-off contacts.

For cars 43241, 43250, 43251, 43260 and 43261. The kit consists of a pickup shoe and a ground spring, a light diffuser with light sockets, 2 light bulbs, and a current-conducting close coupler.

This catenary wire is for adjustment of individual track lengths. One end has the standard eyelets for hanging the wire on a mast, and the other end has a receptacle for a cut catenary wire with an open end. The precise length can be adjusted during installation. 5 pieces to a package.

Length 2 x 1/2 = 2 x 90 mm / 3-9/16". Continuous contact through wheel sets on locomotives / cars. The two track sections have an insulated rail section for track occupation feedback signal when a train is passing over them. The contact area can be lengthened with regular straight and curved track sections.

Functie komt overeen met apparaat 7272. Alle aansluitingen met nieuwe steekverbindingen. Passende stekkers bijgevoegd.

All of the connections on this control box have the new plugs and sockets.Plugs to work with this control box are included.This control box works in the same manner as the 7274 control box.

This is a metal lattice mast. A base with a mounting screw and a slide-on connection is included. This mast is suitable for cross span wires or for single hanger arms. All four sides of the mast have mounting points. This mast can be used for all track systems. Height 170 mm / 6-11/16". One mast to a package.

These springs are for the 73400 or 73401 lighting kits in conjunction with the 72020 current-conducting couplers. This is a set with 5 ground springs for installation in the car trucks.