Hobby & Verzamelartikelen van het thema H0 Märklin K-Track

R3 = radius 553,9mm. Length 1/1 = 30°.

Length 1/1 = 180 mm / 7-3/32". 2 terminal clips for feeder wires. Built-in capacitor for radio/TV interference suppression. Not suitable for Digital and Delta.

Length 2 x 1/2 = 2 x 90 mm / 3-9/16". Continuous contact through wheel sets on locomotives / cars. The two track sections have an insulated rail section for track occupation feedback signal when a train is passing over them. The contact area can be lengthened with regular straight and curved track sections.

2 solenoid mechanisms included. Length of the straight side 168.9 mm / 6-5/8". Turnout branches 2 x 22° 30'. Branch radius 424.6 mm / 16-3/4". Curve same as 2232. 2 additional hand levers included. 6 wires for connections.

This kit is for installing two 75491 turnout mechanisms. It can be adjusted for boards from 8 to 25 mm /approx. 5/16" to 1". Installation template included.

Wide Radius: radius 902,4mm. Length 14° 26'. Complementary curve for 2272/2273/22715/22716 turnout.

This is an improved version of the 7549 turnout mechanism. This mechanism can be used with the 2265 and 2266 turnouts (new versions), the 22715 and 22716 turnouts, the 2275 double slip switch, and the KOMBI extension set program. The mechanism has an automatic end shutoff feature. Automatic feedback is possible with the 72710 control box. Below-baseboard mounting can be done with the 7548 installation kit.

The reed switch is for use at a suitable point with K Track or C Track. The reed switch triggers a pulse of current when a locomotive or car with a magnet mounted on the underside passes over it. The connections to the reed switch are potential-free. The reed switch has a maximum current capacity of 2 amps. Length 38 mm / 1-1/2".

10 pieces of each. These rail joiners and clips are for joints with other track when the 2205 flex track is cut.

Detachable solenoid mechanism (75491) included. Inner curve 30°. Outer curve 30° in the parallel curve spacing of 64.6 mm / 2-1/2". Length and radius of the inner curve are the same as 2221

Detachable solenoid mechanism (75491) included. Inner curve 30°. Outer curve 30° in the parallel curve spacing of 64.6 mm / 2-1/2". Length and radius of the inner curve are the same as 2221.

Detachable solenoid mechanism (75491) included. Crossing angle 22° 30'. Curve same as 2232. Length of the straight side 168.9 mm / 6-5/8".

Detachable solenoid mechanism (75491)included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8".

Detachable hand lever included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8". A 75491 solenoid mechanism can be installed on these turnouts.

Detachable solenoid mechanism (75491)included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8".

Crossing angle 14° 26'. Track length 225 mm / 8-7/8".

2 detachable hand levers included. Crossing angle 14° 26'. Curve radius 902.4 mm / 35-1/2". Length of the straight side 225 mm / 8-7/8". 2 each 75491 solenoid mechanisms can be installed on this unit. Separate paths can be set on the double slip switch.

One each right and left turnout lantern for installation on turnouts with the detachable turnout mechanism. The turnout lantern can be used with hand levers, the 75491 turnout mechanism, or the 7548 below-baseboard mounting kit with a 7549. The lights are maintenance-free LEDs.

200 pieces 1.4 x 10 mm (1/16" x 3/8"), size 00. These screws are for mounting track sections (H0) or for mounting bridge sections on bridge pillars (Märklin Z).

R4 = radius 618,5mm. Length 1/1 = 30°.

6 pieces. 10 x 5 x 1.5 mm / approx. 25/64" x 3/16" x 1/16". This magnet is for activating 7555 reed switches. It is for locomotives with little ground clearance.

3 pieces. 13 x 7 x 2.5 mm (approx. 1/2" x 9/32" x 3/32"). This magnet is for activating 7555 reed switches. It is for locomotives with greater ground clearance.

2 pieces. 10 x 10 x 3 mm / approx. 3/8" x 3/8" x 1/8". This magnet is for activating the 7555 reed switch. It is for freight and passenger cars.

This screwdriver has a cross point size 00 (Ph). For 74990 (C) and 7599 (K) track screws.

Length 1/2 = 15°. Radius 360 mm / 14-3/16". Momentary contact with locomotive/car pickup shoe.

R2 =radius 424.6mm. Length 1/2 = 15°.

Length 1/2 = 90 mm / 3-9/16". Momentary contact with a locomotive/car pickup shoe.

Length 1/2 = 15°.

R2 = Radius 424.6mm. Length 1/1 = 30°.

R2 = radius 424.6mm. Length 3/4 = 22° 30'.

R2 = Radius 424,6mm. Length 1/4 = 7° 30'.

Length 1/4 = 7° 30'.

Length 1/2 = 15°. Radius 424.6 mm / 16-3/4". Momentary contact with a locomotive/car pickup shoe.

Crossing angle 45°. Track length 90 mm / 3-9/16".

Crossing angle 22° 30’. Track length 168.9 mm / 6-5/8".

Length 1/1 = 180 mm / 7-3/32". 2 terminal clips for feeder wires. Only for Delta and Digital.

Length 41.3 mm / 1-5/8".

R1 = Radius 360mm

R2 = radius 424.6mm. Length 1/8 = 3° 45'.

Detachable hand lever included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8". A 75491 solenoid mechanism can be installed on these turnouts.

This can be installed anywhere on the layout under the rails.

Detachable hand lever included. Fixed frog and guard rails. Length of the straight side 225 mm / 8-7/8". Turnout branch 14° 26'. Branch radius 902.4 mm / 35-1/2". A 75491 electric turnout mechanism can be installed on these turnouts

Length 38 mm / 1-1/2". The track bumper can be clipped onto the rails. A wood screw for installation is included.

This is installed between the third rail clips at the ends of the track.

This is installed at rail joints between the third rail clips to separate track circuits. Contents 5 pieces.