Hobby & Verzamelartikelen van het thema Rails en treintoebehoren

Length 220 mm / 8-5/16".

Length 112.8 mm / 4-7/16". Same length as the straight length of 8559 crossing and 8560 double slip switch.

1 German Federal Railroad (DB) class 89 steam locomotive, 1 DB low side car with a tarp, 1 gondola.

Radius 145 mm / 5-3/4". 45°, R1

Radius 220 mm / 8-11/16". 45°.

Length 110 mm / 4-3/8". 13°. Radius 490 mm / 19-1/4".

Length 55 mm / 2-3/16". A manual hand lever is included, or the unit can be remote controlled with the 7272/72720 control box.

Radius 195 mm / 7-11/16". 30° (same as 8521.) Main track length 25 mm / 1".

Length 112.8 mm / 4-7/16". 13°.

Adjustable in length from 100 to 120 mm / 3-15/16" to 4-3/4" for situations where a standard section will not fit.

Length 55 mm / 2-3/16". Terminal clips included. A passing train activates the function.

The track bumper has an LED for a lighted lantern. Length 16 mm / 5/8". The track bumper can be screwed to the end of the track. Wood screw included.

Length 15 mm / 19/32". The track bumper can be clipped to the rails.

Radius 195 mm / 7-11/16". 30° (same as 8521.) Main track length 25 mm / 1".

Length 220 mm / 8-13/16".

R3 = radius 553,9mm. Length 1/1 = 30°.

Two straight track sections, each 94.2 mm / 3-11/16". Continuous contact through wheel sets. With insulated section of rail for track occupation feedback when traversed by a train. Can be extended with regular straight or curved track sections.

This is for retrofitting 2 C Track turnouts. The turnout lanterns can be used right, left, or three-way turnouts. They can be used with a manual hand lever and/or with the 74491 electric turnout mechanism. The lights for the lanterns are maintenance-free warm white LEDs.

Double solenoid mechanism with feedback contacts, end position shutoff, and a locking feature. The turnout mechanism can be mounted on the 5965, 5966, 5976 and 5977 turnouts. It can be operated by remote control using the 7272/72720 or 7271/72710 control boxes (conventional operation) or the 6083/60830 k 83 decoder (digital operation). 3 hookup wires included. Dimensions 67 x 41 x 17 mm / 2-5/8" x 1-5/8" x 5/8".

Component for programming and reading H0 locomotives with built-in c 82 decoder. Can be used in code locomotive addresses, starting voltage, and acceleration and braking delay.

Slanke meegebogen wissel.

This feeder wire set has spade connectors for C Track. The set has two-conductors with a red and a brown wire.

To separate power circuits or signal blocks. 8 pieces for 4 insulation points.

This set is for older color light signals (item nos. 7239 to 7242) and semaphore signals (item nos. 7039 to 7042), which come equipped for operation with K or M Track. The set includes center rail insulators, wires for connections, and hardware for one signal block.

Red and brown feeder wires with spade connectors at both ends, for C Track. Length 2 meters / 78-3/4".

The light mast can be plugged into the Märklin 24997 C-Track or Trix 62997 C-track . The mast signal lights up when the uncoupler track is activated. Metal mast. Height 85 mm / 3-38". This light mast is technically the same as the earlier 5113 mast.

The cross span assembly is a pre-assembled unit consisting of span wires, cross span support wires, and 3 adjustable catenary wire hangers. 2 metal tower masts on bases with mounting screws and slide-on connections are included. The mast spacing can be adjusted up to 235 mm / 9-1/4". The span wires are made of welded steel wire, the cross span support wires are elastic, and the masts and catenary wire hangers are electrically separated from each other. Mast height 150 mm / 5-7/8".

Length 1/1 = 180 mm / 7-3/32". 2 terminal clips for feeder wires. Built-in capacitor for radio/TV interference suppression. Not suitable for Digital and Delta.

Length 2 x 1/2 = 2 x 90 mm / 3-9/16". Continuous contact through wheel sets on locomotives / cars. The two track sections have an insulated rail section for track occupation feedback signal when a train is passing over them. The contact area can be lengthened with regular straight and curved track sections.

2 solenoid mechanisms included. Length of the straight side 168.9 mm / 6-5/8". Turnout branches 2 x 22° 30'. Branch radius 424.6 mm / 16-3/4". Curve same as 2232. 2 additional hand levers included. 6 wires for connections.

This kit is for installing two 75491 turnout mechanisms. It can be adjusted for boards from 8 to 25 mm /approx. 5/16" to 1". Installation template included.

Wide Radius: radius 902,4mm. Length 14° 26'. Complementary curve for 2272/2273/22715/22716 turnout.

This is an improved version of the 7549 turnout mechanism. This mechanism can be used with the 2265 and 2266 turnouts (new versions), the 22715 and 22716 turnouts, the 2275 double slip switch, and the KOMBI extension set program. The mechanism has an automatic end shutoff feature. Automatic feedback is possible with the 72710 control box. Below-baseboard mounting can be done with the 7548 installation kit.

The reed switch is for use at a suitable point with K Track or C Track. The reed switch triggers a pulse of current when a locomotive or car with a magnet mounted on the underside passes over it. The connections to the reed switch are potential-free. The reed switch has a maximum current capacity of 2 amps. Length 38 mm / 1-1/2".

10 pieces of each. These rail joiners and clips are for joints with other track when the 2205 flex track is cut.

Detachable solenoid mechanism (75491) included. Inner curve 30°. Outer curve 30° in the parallel curve spacing of 64.6 mm / 2-1/2". Length and radius of the inner curve are the same as 2221

Detachable solenoid mechanism (75491) included. Inner curve 30°. Outer curve 30° in the parallel curve spacing of 64.6 mm / 2-1/2". Length and radius of the inner curve are the same as 2221.

Detachable solenoid mechanism (75491) included. Crossing angle 22° 30'. Curve same as 2232. Length of the straight side 168.9 mm / 6-5/8".

Detachable solenoid mechanism (75491)included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8".

Detachable solenoid mechanism (75491)included. Turnout branch 22° 30'. Branch same as 2232. Length of the straight side 168.9 mm / 6-5/8".

Crossing angle 14° 26'. Track length 225 mm / 8-7/8".

2 detachable hand levers included. Crossing angle 14° 26'. Curve radius 902.4 mm / 35-1/2". Length of the straight side 225 mm / 8-7/8". 2 each 75491 solenoid mechanisms can be installed on this unit. Separate paths can be set on the double slip switch.

One each right and left turnout lantern for installation on turnouts with the detachable turnout mechanism. The turnout lantern can be used with hand levers, the 75491 turnout mechanism, or the 7548 below-baseboard mounting kit with a 7549. The lights are maintenance-free LEDs.

200 pieces 1.4 x 10 mm (1/16" x 3/8"), size 00. These screws are for mounting track sections (H0) or for mounting bridge sections on bridge pillars (Märklin Z).

This is a metal lattice mast. A base with a mounting screw and a slide-on connection is included. This mast is suitable for cross span wires or for single hanger arms. All four sides of the mast have mounting points. This mast can be used for all track systems. Height 170 mm / 6-11/16". One mast to a package.

This kit is for a custom set-up. It consists of cross span wires, cross span support wires, insulators and 5 catenary wire hangers. 2 tower masts (74142) are required at a distance of up to 500 mm / 19-11/16". The cross span wires are made of steel; the cross span support wires can be realistically tensioned. The catenary wire hangers are electrically insulated. This kit comes with set-up instructions.

This is a signal mechanism with integrated circuits for controlled stopping of digital locomotives with high-efficiency propulsion.

Signal control box for the 70361, 70381, 70391, 70392, 70411, 70412, and 70421 semaphore/target signals and for the 764xx series color light signals. This control box is for operating up to 4 signals. A multi-conductor cable with plugs is included for connecting control boxes together.

The signal has a semaphore and an open narrow mast. The signal changes from red to green.

The signal has 2 independent semaphores and an open narrow mast. The signal changes from red to green or red to green/yellow.

The signal has 2 independent semaphores and an open lattice mast. The signal changes from red to green or red to green/yellow.

Yard signal for use in switching areas.Prototypical thin pipe mast.The Sh1 aspect is correct with 2 white lights.

2 signals on one mast without additional connections. Block signal for use on main lines. Distant signal for use before a block signal or an entry signal.

The signal has a movable disk. The signal changes from yellow/yellow to green/green. It has a double solenoid. A base plate is included.Width 28 mm / 1-1/8". Length 65 mm / 2-9/16". Height 73 mm / 2-7/8".

Changes from red (Hp0) to green (Hp1) or green/yellow (Hp2) and controls track power with double solenoid mechanism with additional third solenoid for the green/yellow aspect. 2 additional hand levers. With base plate. Width 30 mm / 1-3/16*. Length 95 mm / 3-3/4*. Height 90 mm / 3-9/16*.

Changes from yellow/yellow (Vr0) to green/green (Vr1). With 7230 mounting bracket and base plate. Width 16 mm / 5/8*. Length 28 mm / 1-1/8*. Height 67 mm / 2-5/8*.

Changes from yellow/yellow (Vr0) to yellow/green (Vr2). With 7230 mounting bracket and base plate. Width 16 mm / 5/8*. Length 28 mm / 1-1/8*. Height 67 mm / 2-5/8*.

Changes from red/red (Sh0) white/white (Sh1) and controls track power with double solenoid mechanism. Additional hand lever. Width 30 mm / 1-3/16*. Length 70 mm / 2-3/4*. Height 18 mm / 11/16*.

Install from below on a locomotive.

R4 = radius 618,5mm. Length 1/1 = 30°.

Slanke meegebogen wissel.

Type SBS 10 for older design locomotives. Interchangeable with 7218.

Type SBS 65 for modern locomotives. Interchangeable with 7218.

For cars 4035, 4038, 4039, 4107 and 4108. The kit consists of a pickup shoe with a light socket and a light bulb.

6 pieces. 10 x 5 x 1.5 mm / approx. 25/64" x 3/16" x 1/16". This magnet is for activating 7555 reed switches. It is for locomotives with little ground clearance.

3 pieces. 13 x 7 x 2.5 mm (approx. 1/2" x 9/32" x 3/32"). This magnet is for activating 7555 reed switches. It is for locomotives with greater ground clearance.