Hobby & Verzamelartikelen van het thema Rails en treintoebehoren

This track is the same length as the parallel track spacing for the wide radius turnouts and wide angle crossings.

Serves as the complement to the length of the complementary curve on the wide radius turnouts and wide angle crossings.

Radius 145 mm / 5-3/4". 45°, R1

Radius 220 mm / 8-11/16". 45°.

Length 110 mm / 4-3/8". 13°. Radius 490 mm / 19-1/4".

Length 55 mm / 2-3/16". A manual hand lever is included, or the unit can be remote controlled with the 7272/72720 control box.

Radius 195 mm / 7-11/16". 30° (same as 8521.) Main track length 25 mm / 1".

Length 112.8 mm / 4-7/16". 13°.

Adjustable in length from 100 to 120 mm / 3-15/16" to 4-3/4" for situations where a standard section will not fit.

Length 55 mm / 2-3/16". Terminal clips included. A passing train activates the function.

R1 = 360 mm

The track bumper has an LED for a lighted lantern. Length 16 mm / 5/8". The track bumper can be screwed to the end of the track. Wood screw included.

Length 15 mm / 19/32". The track bumper can be clipped to the rails.

4 LED's, red-red, yellow-yellow

Radius 195 mm / 7-11/16". 30° (same as 8521.) Main track length 25 mm / 1".

Length 220 mm / 8-13/16".

Diameter 2.5 mm.

R3 = radius 553,9mm. Length 1/1 = 30°.

Two straight track sections, each 94.2 mm / 3-11/16". Continuous contact through wheel sets. With insulated section of rail for track occupation feedback when traversed by a train. Can be extended with regular straight or curved track sections.

R4 = 430 mm. Buiten diameter 877 mm.
12 stuks nodig voor een cirkel.

R3 = 396,4 mm. Buiten diameter 810 mm.

R4 = radius 618,5mm. Length 1/1 = 30°.

Slanke meegebogen wissel.

R 2 - 24° Gapped in both rails for electrical isolation.

This controller (momentary contact) is for semaphore/target signals, turnouts, uncoupler tracks, and relays and comes with an additional contact that serves as a track current controller for an automatic train control feature.

A frame with a buffer beam comes mounted on the track. The rails end in the roadbed.

Radius 220 mm / 8-11/16". 30°. Terminal clips included. A passing train activates the function.

Length 55 mm / 2-3/16". Terminal clips included. One rail is gapped in the middle.

This controller enables automatic stops and independent startup of trains in a station, etc. The stopping time can be adjusted smoothly. This controller is not suitable for Selectrix operation!

Used for the diagonal crossing tracks.

R1 = 356,5mm Radius

R2 = 420 mm Radius

R2 = 420 mm Radius

Radius 195 mm / 7-11/16". 30°. Terminal clips included. A passing train activates the function.

This controller is for operating four turnouts, signals or relays (momentary contact).

Is required if many individual supply lines (eg switches, signals, lighting, etc.) have to be connected to a common pole. 2 electrically isolated terminal strips each with 6 pressure terminals, a total of 12 terminals, allowing connection of at least 24 cables!

With 3 electrically isolated pressure clamps. Especially to use when extending the signal and switch connection, but also as a small distributor plate.

Dual magnetic drive for a maximum of 14 volts AC or DC. To trigger pulse contacts are required. With limit switch.

ROCO-Clean replacement wiper for the H0 “ROCO-Clean” rail-cleaning car, 46400.

Length 25 mm / 1".

Length 110 mm / 4-3/8". 13°. Radius 490 mm / 19-1/4".

Length 110 mm / 4-3/8". 13°. Radius 490 mm / 19-1/4".

Length 110 mm / 4-3/8". 13°. Radius 490 mm / 19-1/4".

R2 = 437,5 mm

The ideal large transformer for all requirements. Extremely powerful, with a short circuit indicator light for both track feed and AC feed. With multisensible speed controller and definite forwards and backwards control. Automatische overload protection. The controller gives a definite forwards and backwards control and speed settings. The control knob clicks gently into a zero position. Automatic overload protection. easy connection to the layout using the pressure connection clips.Technical data:■ Running voltage: 0–15 V= / 1.1 A■ Separate accessory output: 14 V~ / 1.0 A

R2 =radius 424.6mm. Length 1/2 = 15°.

Length 1/2 = 90 mm / 3-9/16". Momentary contact with a locomotive/car pickup shoe.

R2 = Radius 424.6mm. Length 1/1 = 30°.

R2 = radius 424.6mm. Length 3/4 = 22° 30'.

R2 = Radius 424,6mm. Length 1/4 = 7° 30'.

Length 1/2 = 15°. Radius 424.6 mm / 16-3/4". Momentary contact with a locomotive/car pickup shoe.

Crossing angle 45°. Track length 90 mm / 3-9/16".

Crossing angle 22° 30’. Track length 168.9 mm / 6-5/8".

Length 1/1 = 180 mm / 7-3/32". 2 terminal clips for feeder wires. Only for Delta and Digital.

Radius 195 mm / 7-11/16". 30°.

Length 108.6 mm / 4-1/4". For adjusting length on the 8559 crossing and 8560 double slip switch.

Radius R1: 194,6 mm. 12 Stuks nodig voor een cirkel.